Thread: Raising the X
Results 41 to 60 of 256
-
-
-
11-17-2009 12:16 PM
I didn't use wood in the stringers, bulkheads and floor, I used coosa and divyncell. The transom is original except for the portion I filled to raise the outdrive and it is still wood. The engine stringers are wood as well. I believe wood is the best material for a transom because of the compression strength and the screw holding.
-
-
- Join Date
- Oct 2008
- Location
- Lake Travis Texas
- Posts
- 6,844
11-17-2009 09:18 PMI agree the transom and stringers where the engines mount should be wood. Everything else can be something else.
-
11-17-2009 10:01 PM
I don't think Azek would be good for anything in boat. It's heavy as hell and not that strong for the weight. If you really want to do a composite coosa bluewater 26 would probably be good but it is expensive and not necessary. The wood transom lasted almost 20 years without being properly sealed. If you do it right it will last forever.
-
11-17-2009 10:40 PM
I do think sealing it up may be the key. When I have it apart I will make sure there is no bear wood left untreated. I am still working on my hoist in my building. I have a I Beam on order, I am going to get a 2 or 3 ton trolley and chain hoist.
-
11-18-2009 12:44 PM
Jeffsway i would recomend a good marine grade plywood and if you have to buy a full sheet of 3/4 it will run around $ 90 a sheet .
Last edited by Offshore Ginger; 11-18-2009 at 01:31 PM.
-
11-18-2009 06:24 PM
Got my I Beam in today for my hoist. One step closer to starting the project.
-
-
11-18-2009 08:02 PM
I have only had my building for 2 years (42wx60dx12h). I always thought it would be handy to have a hoist. My friend owns a Iron Shop and picked me up a 20' I Beam. We are going to tie one end of the beam to the buildings framework (3) 2x6's, the other end will bolt to the roof truss. When I use it for lifting I will attach a post from the beam to a concrete pad. I will have side to side movement, however the boat or whatever I am lifting will need to be moved forward or back manually. I only have a small amount of concrete so a roll-around hoist would not work well for me. Things do not roll well on gravel. I will take a few pics of it after I get it constructed.
-
-
12-05-2009 07:35 PM
Ok, the hoist is in hear are the pictures.
-
12-05-2009 07:59 PM
l@@kin good and you should be ready for just about anything .
-
12-05-2009 08:07 PM
-
-
12-06-2009 09:26 PM
Pulling the engine on the new hoist.
-
12-06-2009 09:34 PM
Transom is not looking good. Looks like I will be doing a complete tearout and reconstruction. The entire bottom half is soft, looks like it was leaking around the seal. The gell has a wear spot around it, do you guys think the housing was leaking? The nuts were not very tight, do you think they may have backed off. Should I replace the rubber seal? Good news is the stringers seem solid. I may beef them up with a sheet of 3/4 marine ply on both sides and make it more rigid. Any input at this point is appreciated.
-
12-06-2009 09:39 PM
Here are the pics.
-
- Join Date
- Oct 2008
- Location
- Lake Travis Texas
- Posts
- 6,844
12-06-2009 09:47 PMThe bolts only get torqued to 25 ft/lbs.. I suspect the soft wood was the issue and the bolts did not come loose or have anything to do with the leak.