Thanks T2x. Appreciate the info. Guess it's not an option for what I was thinking. Outstanding looking piece, though. You must have really enjoyed running them.
I have a friend who's looking at buying a SST45 boat and getting started. My wife won't let get back in, afraid I'll kill myself.....
Thread: T2 Outboard on ebay
Results 21 to 37 of 37
-
- Join Date
- Oct 2008
- Location
- West Michigan
- Posts
- 37,872
- Blog Entries
- 45
03-23-2009 08:40 AMGetting bad advice is unfortunate, taking bad advice is a Serious matter!!
-
03-23-2009 10:22 AM
Twister 1...3 carb side exhaust....first Twister AKA "T-1"
Allergic to Nonsense
-
- Join Date
- Nov 2008
- Posts
- 2
03-23-2009 10:45 AMIf someone wants me to take a look at it for them, give me a call. I'm only 20 mins north of Port St Lucie
Mike
734-777-1878
-
- Join Date
- Oct 2008
- Posts
- 39
03-23-2009 11:12 AMAlso known as a silo motor which was built out of Oshkosh engineering, Bob Morgan was in charge, he built the first prototypes, then Dave Bair and I built the rest. Later the bottom of the manifold was opened up and we bolted on open exhaust nicknammed cow bells, those were really cool motors. Remember Bair and I worked for Garbrecht at 20 wisconsin street in Oshkosh which was the OPC racing division. All the power head serial numbers from that era either started with DB or RP. That was when we had Bob Herring, Tom Stickle, Mike Downard, and Jim Merten as full time employees. Sub contract we had Sirois, Habe, Pruitt, Miles, Clark, percival,Molinari,Wilson, John Henry, Fountain, etc. Those were the days. Parker, Miami nationals, Havasau, Paris, Chasewater, etc etc etc. Great days great friends, sadly many lost their lives, or became crippled from those racing days.
-
- Join Date
- Oct 2008
- Location
- West Michigan
- Posts
- 37,872
- Blog Entries
- 45
-
Slippery when wet. PODLESS TUNNEL www.cheetahcat.com ,Repairs, Modifications and Truing Cheap reliable speed.
-
- Join Date
- Oct 2008
- Posts
- 907
-
- Join Date
- Oct 2008
- Location
- West Michigan
- Posts
- 37,872
- Blog Entries
- 45
-
-
-
- Join Date
- Oct 2008
- Location
- West Michigan
- Posts
- 37,872
- Blog Entries
- 45
-
03-24-2009 09:53 AM
Maybe a little...... might run a bit cooler as well.
We ran them normally up to about 7200-7600 RPM as I recall...and the components were just about maxed out at that point. I had one engine which we built with a super secret resurfacing technology on the pistons, bearings and rings that had gobs more power than any other powerhead I ever ran (and I ran dozens)....... That engine spun up to 8500 RPM during a test lap at unbelievable speed and grenaded. The rods simply couldn't handle the stresses. By the way, I never achieved the same speed again on that hull (see photo)...even with the early V-6's(pictured).
I kept a spare T2x powerhead for a future coffee table, back in the 70's in a boatyard on Lake Hopatcong. I went back 10 years later and it was gone.
T2xAllergic to Nonsense
-
03-24-2009 10:03 AM
Some of my other T2x hulls from back in the day.........
T2xAllergic to Nonsense
-
- Join Date
- Oct 2008
- Location
- West Michigan
- Posts
- 37,872
- Blog Entries
- 45
03-24-2009 11:46 AMThat's too bad. It would be fun to copy that and use today's rod technology to see if it would stay together. We've spun our RC motors over 20,000 rpm (real short stroke). Sounds like a project we could pull off and use to christian the Miami Boat Stadium when it's done..... Wanna drive?
That's too bad, do you still want one? We could all start lookin.Getting bad advice is unfortunate, taking bad advice is a Serious matter!!
-
03-25-2009 10:18 PM
ended at $3,440.00 reserve not met. Oh well maybe it will show up again.
-
-