My '99 Chevy 5.3L suddenly gained 20 PSI of oil pressure. It was always solid at 40 PSI. Now it's 60 PSI driving and 50 PSI at idle hot or cold.
Oil is still honey colored since my last change. I use Amsoil 5W30 with Purolator PureOne filter.
Now, I'm afraid to try towing the boat
Any thoughts?
Thread: Oil Pressuer Jumped 20 PSI
Results 1 to 15 of 15
-
- Join Date
- Oct 2008
- Location
- Appleton, Wisconsin. Where we have 2 seasons... winter and road construction
- Posts
- 4,120
05-23-2010 10:27 AM•_•_•_▬_▬_▬_•_•_•
-
- Join Date
- Oct 2008
- Posts
- 4,796
05-23-2010 11:04 AMChange oil filters. You may have had an internal failure. You could be getting very low flow and all your pump's output could be blowing right into the pan through the pump's bypass.
No recent changes? Is the oiling system all stock? I've seen mis-plumbed remote coolers that had the circulation going backwards. That can make a filter fail- usually pretty quickly.
-
- Join Date
- Oct 2008
- Location
- West Michigan
- Posts
- 37,354
- Blog Entries
- 44
-
-
- Join Date
- Oct 2008
- Location
- Appleton, Wisconsin. Where we have 2 seasons... winter and road construction
- Posts
- 4,120
05-23-2010 01:30 PMI wanted to check the drain plug magnet, so I did a complete oil change. The magnet looked fine, oil filter looks fine. Now what....sending unit?
Fricking 81° here and I'm stuck in the garage instead of on the water•_•_•_▬_▬_▬_•_•_•
-
05-23-2010 03:14 PM
so ?
does Santa's sleigh have a blower ?
-
- Join Date
- Oct 2008
- Location
- Appleton, Wisconsin. Where we have 2 seasons... winter and road construction
- Posts
- 4,120
05-23-2010 04:46 PMPressure is still high. I need to get my hands on a scan tool and see what the computer is seeing from the sensor. If the sensor is reading high, then a new sensor. If the sensor is reading normal, but the gauge is high, a new stepper motor for the gauge.
•_•_•_▬_▬_▬_•_•_•
-
- Join Date
- Oct 2008
- Location
- Appleton, Wisconsin. Where we have 2 seasons... winter and road construction
- Posts
- 4,120
05-23-2010 04:47 PMI wish I could test the sensor, but the mofo is buried behind the intake. Where the distributer used to be on Chevy's. I can barely see the damn thing.
•_•_•_▬_▬_▬_•_•_•
-
05-23-2010 06:23 PM
How does the motor sound at idle while running? Any noiser than it use to be? I've seen a main or rod bearing turn which blocks off an oil passage, thus increases oil pressure.
-
-
- Join Date
- Oct 2008
- Location
- Appleton, Wisconsin. Where we have 2 seasons... winter and road construction
- Posts
- 4,120
05-23-2010 06:40 PMI was looking for the location of the sending unit and I found a mouse nest on my intake! Now I'm wondering if the little chit(s) messed with the wiring?
•_•_•_▬_▬_▬_•_•_•
-
- Join Date
- Oct 2008
- Posts
- 4,796
05-23-2010 07:48 PMMice ate the wiring on my lawn tractor last winter. Again. What is it with vinyl wiring insulation?
-
- Join Date
- Oct 2008
- Location
- Appleton, Wisconsin. Where we have 2 seasons... winter and road construction
- Posts
- 4,120
05-24-2010 01:20 PMI had a service call at a McD's for a lot light that kept tripping the breaker. Mice had climbed the three wires dangling 25' down from the top of the pole and made a nice mouse house in the 4" X 4" crossarm at the top of the pole. And yes, most of the wires insulation in the crossarm was missing. How they managed to climb up those three wires is amazing.
•_•_•_▬_▬_▬_•_•_•
-
- Join Date
- Oct 2008
- Location
- Appleton, Wisconsin. Where we have 2 seasons... winter and road construction
- Posts
- 4,120
05-24-2010 01:25 PMI have a strong feeling the sending units wire was gnawed into and the road grime on the wiring harness is giving the elevated reading. Now I just need to remove all the pretty plastic crap on top of the engine to check into this.
I'm gonna be pissed if I missed a great boating day over a fricking mouse•_•_•_▬_▬_▬_•_•_•
-