Search:

Type: Posts; User: 1stoutlaw

Page 1 of 4 1 2 3 4
Search: Search took 0.00 seconds.
  1. Replies
    5
    Views
    6,088

    Ratickle---nothing to muff the exhausts--I guess...

    Ratickle---nothing to muff the exhausts--I guess they are really called semi-dry----the water mixes with the main exhaust at about a inch from the end/outside---they were not really that much louder...
  2. Replies
    5
    Views
    6,088

    Engine / Camshaft Guys !!!

    OK--blew my brand new 502 / 502 engine w/ a bad crankshaft bearing (19HRS)......Block and crank are back from the machine shop and she is ready to re-build---I have the ZZ 502 / 502...
  3. Replies
    11
    Views
    8,122

    OK---long story short---found a piece of a broken...

    OK---long story short---found a piece of a broken snap ring inside the distributor---stuck/attached to the magnetic pick up-----it would move and lock up the spinning gear----bottom gear was brand...
  4. Replies
    11
    Views
    8,122

    RSchap1---right now I guess it has to be anyone...

    RSchap1---right now I guess it has to be anyone of the above you listed--my engine tech does not want me to touch her anymore and to bring her in for him to look at---he believed it was the ignition...
  5. Replies
    11
    Views
    8,122

    OK---changed over the ignition system to the MSD...

    OK---changed over the ignition system to the MSD system they sent me----SAME F------- PROBLEM....backfires out the exhaust----then just spins like a top---give her a squirt of gas---boooom out the...
  6. Replies
    11
    Views
    8,122

    OK---after several weeks of waiting-KE...

    OK---after several weeks of waiting-KE Performance phoned and told me the ignition box was no good--wheeeew!!!!! I'm glad it was that-----So they are sending me a MSD anolog vs. the new digital boxes...
  7. Replies
    11
    Views
    8,122

    Yes Ratickle--- I have 9 hours on the...

    Yes Ratickle--- I have 9 hours on the engine----probably 6 hours in the water vs the engine stand-----and she ran GREAT!!!!! I mailed the Max Volt blue box back to KE Performance where I bought...
  8. Thread: Oil Temp ???

    by 1stoutlaw
    Replies
    14
    Views
    9,712

    OK----my oil temp has been running here in...

    OK----my oil temp has been running here in Florida---215--225----!!!!! I asume from u guys answers - that should be good--------Thanks--Mike-Tampa Bay
  9. Replies
    11
    Views
    8,122

    Brand New Engine Backfires !!!

    OK----this has been over 2 year project----replaced a 6.2 Merc w/ a 502/502 custom engine----everything brand new-did not use any parts / accessories from my blown engine----Have 9 hours on...
  10. Replies
    8
    Views
    6,466

    MOBILMERCMAN---Thanks soooo much for that...

    MOBILMERCMAN---Thanks soooo much for that info----I have learned to save a buck--cost me more bucks---I have to pull out the engine again----AND I have learned to be aware what U wish for!!!!!! ...
  11. Replies
    8
    Views
    6,466

    Thanks Ratickle----I will talk to the engine...

    Thanks Ratickle----I will talk to the engine company and ask about the balancing and go from there!!!
  12. Replies
    8
    Views
    6,466

    Thanks----I have been doing some re-search and am...

    Thanks----I have been doing some re-search and am learning some engines are balanced internally and some externally and the 496 flywheel will not be balanced the same as a 502---Soo I need to pull...
  13. Replies
    8
    Views
    6,466

    Engine vibration

    Engine is finally in the boat--BUT has a bad vibration--trying to save a buck, I installed a barley used 496 flywheel on this new 502!!!! Is this flywheel an OK fit or could that be the...
  14. Replies
    9
    Views
    1,883

    awsome video !!!

    awsome video !!!
  15. Thread: Oil Temp ???

    by 1stoutlaw
    Replies
    14
    Views
    9,712

    Thanks----I have never had a oil temp gauge--nor...

    Thanks----I have never had a oil temp gauge--nor any of my friends boats---SOOooo it is a new learning experiance !!!!! Mike-Tampa Bay !!!
  16. Replies
    15
    Views
    9,255

    thanks again----I will see my buddy this next...

    thanks again----I will see my buddy this next week----look over the boat and think about the points you brought up---The motor we believe is original 1995 Outlaw 454/330 hp----it was just recently...
  17. Thread: Oil Temp ???

    by 1stoutlaw
    Replies
    14
    Views
    9,712

    Thanks again----The gauge is in and I hope to put...

    Thanks again----The gauge is in and I hope to put her in the water this week......
  18. Replies
    15
    Views
    9,255

    Hmmmn should we put her down close to the...

    Hmmmn should we put her down close to the tank--run the hose in a circle to hold gas...and try that????? He just bought this boat, so we don't know if the previous owner had this problem or not?? He...
  19. Thread: Oil Temp ???

    by 1stoutlaw
    Replies
    14
    Views
    9,712

    Oil Temp ???

    Getting ready to run a new 502 engine in my 25' Outlaw----picked up a oil temp gauge today.....was told I need one---The sensor is installed into the oil filter bracket (Hardin Marine) !!!!!! The...
  20. Replies
    15
    Views
    9,255

    Thanks--YES his electric fuel pump is mounted in...

    Thanks--YES his electric fuel pump is mounted in the back, on the head, the height of the valve cover !!! AND the fuel hose from the tank comes from tank (floor height) up hill !!!! We will look at...
  21. Replies
    38
    Views
    15,335

    OK---I have water reversion after all !!!!! I...

    OK---I have water reversion after all !!!!! I have ordered a set of custom risers from Stainless Marine here in Florida...I'm told the riser will go up 12" and the water won't mix with the exhaust...
  22. Replies
    10
    Views
    4,987

    Cam is from a zz 502 engine, act !!!!actually...

    Cam is from a zz 502 engine, act !!!!actually you found the cam specs for me-------I posted this in the wrong section---I will re-post under my Cam Post
  23. Replies
    10
    Views
    4,987

    OK---engine runs great---exhaust manifold bolt...

    OK---engine runs great---exhaust manifold bolt was loose as we took her off to check for reversion------YES w/ this cam I have water reversion----Engine is finally in the boat--all...
  24. Replies
    15
    Views
    9,255

    OK---We bought a carb rebuild kit from...

    OK---We bought a carb rebuild kit from Pep-Boys----Yes.. they sell a Marine carb kit----same jets--ect-----and us.. two DYI clowns cleaned her with Power tune--new jets--new washers/gaskets----ran...
  25. Replies
    15
    Views
    9,255

    Ratickle--thanks--I was told the fuel pump is not...

    Ratickle--thanks--I was told the fuel pump is not up to par----pouring gas down the carb starts the engine--the engine pulls fuel up the line w/ some help of the fuel pump--at idle there is enough...
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4