Search:

I bet he is speaking of, nickel colbalt alloy. I talked with my sales rep. from CV Products about this. There is a patent on this alloy, out side of that, they have not seen a reason to offer it. I...

Take-Out Parts from a Nor-Tech 850 SC, Parts have 116 Hours
Cams 2 Crane 256/ .632 262/.632 112 HR $125 each
Lifters 2 sets Crane Hydraulic with tie bar $130 per set
Rockers 2 sets Crane...

CP has released there Bullet Series Pistons. They are a 2618 Alloy, same quality as the CP shelf stock and customs. They come with pins, wire locks, support rails if needed, and rings. I have used CP...

Water pressure can vary at different locations in the system. Higher before it reaches the sea-strainer, lower at exiting. My experience has been that the pressure seems to be the same either at the...

I'am pretty sure the mfg date is 07, I have seen dated and undated in the past. Are you going to inspect the lifters?

Fixxxer22
As said, by Eddie and Bob, always check the lifter bore clearance not only for clearance, but also for being out of round. The Morel, lifter is what I use on every build. The problem with...

I did some thru hull pick-ups on a 33 Fountain, we had to install a square piece of plywood for backing for the pick-ups on the inside of the hull.

I use the Napa clear power steering fluid. When bleeding after rebuild, of course you want to fill reserivor, cap the down fittings on the trim line manifold block, tap the up button until clear...

No crank, rods or pistons. It was one of those deals, I ordered, pistons, rods, cranks and the guy forgot to mail the money over a 6 month period. So this is what I have left over. This was 3 yrs ago.

If you already have run this in salt water over time, I would question at this time of adding a closed cooling, unless you have this torn down at this time and are rebuilding it. You would have to...

I have a Dart 10.200" with splayed billet caps, 4.600 bore. Block is painted. This block is new, it was assembled then torn-down. I also have a NEW BDS 8-71 Tall deck intake, blower, Superchiller...

I have ONE BDS 8-71 tall deck NEW, polished intake, Superchiller, 8-71, with a 4500 adapter plate, belt and pulleys. Steal it for $2500.00

I like the window defroster.

The 11.100" deck height block is going to allow you to run more stroke and lower the rod angle, by reducing the side load on the cylinder wall. Depending on what stroke, rpms you will be running is...

The 6.585 lenght is odd, but not if Merc did it. It's not an standard rod lenght for off the shelf.

9.800 deck, 4.00 stroke, 6.585 rod, if that is the case the compression height would be 1.200 figuring the piston is -.015 below deck. Shortest compreseion height for shelf stock pistons 1.270. If...

What it comes down to; when that stainless exhaust valve is bouncing around the chamber, at that time you'll say; should have bought inconel. You can get Manley or Ferrea. Manley about $45, Ferrea...

I just replaced one just like that on a 47 Fountain w triples. The pin looked like it was fractured long before it failed.

You might want to try Mark Boos, @ Precision Marine

Competition Products, they have blems for about $1200

I spoke with them today first thing, they have gotten away from the ceramic and have switched to sand, they were having problems with core shift. Cost was the other factor. By the way they have...

No, Ray has his own casting company.

I'll have to mention that to the guys Monday. I guess if it's not Dart, World, Brodix, AFR, Edelbrock, people think it's made in China.

NO! They are cast in Ohio, and machined in North Carolina. Ray Franks, company started by casting aircraft parts. The castings are some of the best I have ever seen, the casting is a ceramic mold or...

Ray, You are right! I have used them on N/A and supercharged, on the supercharged you have to add more fuel and boost due to the flow. I have used the 12 degree heads also. As you know the castings...