New Intercoolers [Archive] - SeriousOffshore.com

EXCESS ENERGY

11-06-2010, 11:51 PM

Proto-type cases are machined and being fitted on the motor, and cores shoould be here next week. I will have some pics within the next day or two. :D

Jason, sounds good can't wait, this waiting on parts is getting old. Nothing directed towards you guys at all, just every other vendor out there in the boating world. Everyone on my end is exited. Bob:cheers2:

EXCESS ENERGY

11-06-2010, 11:57 PM

I think those are for the 1500 saxman engines :sifone:

Also for some 600" SVO FORD motors. BOB :driving:

Coolerman

11-07-2010, 03:05 AM

Its about time! I assume these are the intercoolers for the bt w/1200 spiker engines. Too bad you summer is gone.

I think Spiker finally found some whipples..... not 100% sure. I know he has already dynoed his engines and setup his belt/pulley package for the whipples, as well as his water system. But, I do think that our coolers would be very adavantageous for his boat since he is running pump gas..... but it would be alot of extra work for him to switch over at this point.

Coolerman

11-07-2010, 03:05 AM

I think those are for the 1500 saxman engines :sifone:

where did you get the 1500 # number from..... :huh::rofl::sifone:

Coolerman

11-07-2010, 03:12 AM

Jason, sounds good can't wait, this waiting on parts is getting old. Nothing directed towards you guys at all, just every other vendor out there in the boating world. Everyone on my end is exited. Bob:cheers2:

Hey Bob, I know what you mean about waiting on vendors...... I know that we have said certain dates that we were hoping to have this done by, but everything that could have taken longer on our project has.... It's tough trying to develop a new product within specific timeframe. Our plan is to stock these coolers so that when somebody calls up, we can ship one on the same day or the following business day. IE, we don't want to be turn into a vendor that is a pain to get product from.

We have the proto-type cases now which will allow us to at least get performance numbers/testing going on the dyno while we perfect the looks of the cooler, as well as its ease of use for different distributors and water systems.

We are also working on other possible products.... Belt tensioner systems and partial water systems. Might stock some belts and pulleys as well. We'll see... My father and I both have alot of irons in the fire right now so we don't want to bite off more than we can chew.

Coolerman

11-07-2010, 03:18 AM

Also for some 600" SVO FORD motors. BOB :driving:

lol...... 600" SVO + Tunnel Ram + 5" intercooler + PSI + Carb plenum= One fuggin tall motor!!! :sifone::hurray::rofl:

Ratickle

11-07-2010, 09:12 AM

lol...... 600" SVO + Tunnel Ram + 5" intercooler + PSI + Carb plenum= One fuggin tall motor!!! :sifone::hurray::rofl:

And a really big scoop.......

EXCESS ENERGY

11-07-2010, 09:29 AM

Hey Bob, I know what you mean about waiting on vendors...... I know that we have said certain dates that we were hoping to have this done by, but everything that could have taken longer on our project has.... It's tough trying to develop a new product within specific timeframe. Our plan is to stock these coolers so that when somebody calls up, we can ship one on the same day or the following business day. IE, we don't want to be turn into a vendor that is a pain to get product from.

We have the proto-type cases now which will allow us to at least get performance numbers/testing going on the dyno while we perfect the looks of the cooler, as well as its ease of use for different distributors and water systems.

We are also working on other possible products.... Belt tensioner systems and partial water systems. Might stock some belts and pulleys as well. We'll see... My father and I both have alot of irons in the fire right now so we don't want to bite off more than we can chew.
Jason, Sounds like you guys have been real busy. All the product you're working sounds good. Good luck. Bob

EXCESS ENERGY

11-07-2010, 09:42 AM

lol...... 600" SVO + Tunnel Ram + 5" intercooler + PSI + Carb plenum= One fuggin tall motor!!! :sifone::hurray::rofl:

Jason, the tunnel ram is 1.88" taller then the single dominator manifold. We'll see. Bob

Coolerman

11-07-2010, 02:53 PM

Jason, the tunnel ram is 1.88" taller then the single dominator manifold. We'll see. Bob

haha, but still much taller than a regular blower manifold :cool:

What % over are you thinking of spinning the blowers?

endeavor1

11-07-2010, 05:38 PM

interesting thread Sax

Coolerman

11-15-2010, 10:27 PM

1st 2 pics are the new prototype cases. We are going to put the water inlets/outles on the front/back instead of the sides. Might also put some "shape" on the outside of the case so it doesn't look like a box. What do you guys think? We also plan on having the standard finish as a black hard anodized, with the option of polishing or a custom color anodized finish.

Just to clarify height Dimensions, these are the standard height intercoolers for a PSI motor. Normally, you run a 4.25" intercooler with the .75" PSI adapter plate. We integrated the plate into the cooler. The total height of our cooler is 5". We can also cut the inlets for an xx-71 blower. These bolt right on top of a blowershop manifold.

Ok, throw your opinions at me! Should we put our name on the side of it? On the Front? We have some ideas, but obviously some smart people with a good sense style hang out here, so it would great to get everyone's opinion. Any other comments/suggestions are more than welcome.

Also, the last pic is of our old intercooler that we built.

endeavor1

11-15-2010, 11:45 PM

Name on the side

like the idea of the finishes

CMI headers

polished psi

options for side or f/r water flow

Coolerman

11-16-2010, 01:44 AM

CMI headers

That might take a few years....... After we order them. :rolleyes:

carter38

11-16-2010, 04:42 AM

Man that is awesome!

rschap1

11-16-2010, 09:15 AM

NICE!!!

Nevr2nd

11-16-2010, 04:06 PM

Sax, looks killer!!

endeavor1

11-16-2010, 08:23 PM

Sax, looks gay as hell!!, i mean come one, WTF, i wanted to see tribal flames and optional margarita makers mounted to this thing. Back to the drawing board for you i guess

:iagree:

Nevr2nd

11-16-2010, 09:09 PM

Endeavor,
Not sure if you are a mind reader..... or writing using my name. Lol.

No tribal crap, u may as well put a tic tac toe on it!

Everyone knows I prefer snow-cones, hope it has a ice dispenser.(C-16 flavor).

Hope this as well as Endeavor's wisdom helps in your decision making process.:-).

Coolerman

11-16-2010, 11:26 PM

ROTFLMAO!!!!! Ice Disepenser... Never2nd, so far we offer 2 flavors: 100ll and C16. Still pending FDA approval because lead is supposedly unsafe to eat....... :D :D Oh you guys are a big help, oddly enough :26::huh: :rofl:

endeavor1

11-17-2010, 08:38 PM

LMAO, i was hoping i didnt offend never2nd too much. Sax, got the tub cleaned out last night and only pissed the kid off one more time before he went to sleep.

Coolers are coming along great it sounds like. Good luck on ur date

EXCESS ENERGY

11-17-2010, 09:24 PM

Jason, thanks for the e-mail. Those thing are BAD ASS I perfer polished. I"m a gluton for punishment. Can't wait for the test results. Thanks again , Bob

Nevr2nd

11-19-2010, 06:02 PM

Oooooh Endeavor, ha ha, no worries over here. I was laughing and trying to type.(deadly combo)

Sax, I know a way to get the FDA to look the other way. With "poop slices" from our favorite turd cutter!!!

I agree with the polished look, I think it will look bitch like that. Afterall every soft serve ice container is polished, just add sprinkles.

Coolerman

12-01-2010, 09:05 PM

The cores came in today!

EXCESS ENERGY

12-01-2010, 09:46 PM

The cores came in today!

Yipeeeeeeeeeeeeeeeeeeee Bob

endeavor1

12-02-2010, 06:02 PM

My new sex toys came in today!

:eek: :sifone:

Coolerman

12-02-2010, 11:45 PM

:eek: :sifone:

not those cores..... ass. :toetap05:

Coolerman

12-06-2010, 11:49 AM

here are a few more pics of them

Coolerman

12-06-2010, 11:49 AM

cases

endeavor1

12-07-2010, 01:39 AM

So coolerman, i uh mean Saxman, what do those shiny thingys doa again...... lol

Good job on those and good luck to you and Dennis

John P

12-07-2010, 09:03 AM

What size blowers fit these?

I think on the Red Green Show Harold made one of those out of a old heater core and Duct tape. :drool5:

Coolerman

12-07-2010, 10:59 AM

So coolerman, i uh mean Saxman, what do those shiny thingys doa again...... lol

Good job on those and good luck to you and Dennis

Our blowers have the satin finish..... Mr.ExcessEnergy is a glutton for punishment and got his blowers polished! :D:D

Coolerman

12-07-2010, 11:06 AM

What size blowers fit these?

I think on the Red Green Show Harold made one of those out of a old heater core and Duct tape. :drool5:

Any blower with a roots bolt pattern will go on top.

Here is my favorite red green bit http://www.youtube.com/watch?v=TCISlfory98

Nevr2nd

12-07-2010, 12:43 PM

Any blower with a roots bolt pattern will go on top.

Here is my favorite red green bit http://www.youtube.com/watch?v=TCISlfory98

Sax,
I like the new tow rig, the customization is unheard of, and I mean UNHEARD OF!!

I'm ready for my C-16 flavored snow cone.

Coolerman

12-07-2010, 03:05 PM

Sax,
I like the new tow rig, the customization is unheard of, and I mean UNHEARD OF!!

I'm ready for my C-16 flavored snow cone.

Lmao..... hahaha! Done right, I think that could actually be a fun tow rig..... Something must be wrong with me to actually think thats a cool idea!

Snowcones are almost done.... Should be testing some flavors in a few weeks. :party:

John P

12-07-2010, 07:35 PM

Any blower with a roots bolt pattern will go on top.

Here is my favorite red green bit http://www.youtube.com/watch?v=TCISlfory98

I can't say I seen that one. He sure thinks outside the box.

Coolerman

12-24-2010, 06:28 AM

Here is a pre-liminary drawing of our new water pickups that we will be building for our new water system. The 120* bend provides a nice water flow path, and the water scoop is adjustable to provide any amount of water that is needed.

John P

12-24-2010, 09:42 AM

I was able to see the first proto type they came up with and they had to change a lot to get it where it is now.

68293

Merry Xmas!!

Coolerman

12-24-2010, 11:24 AM

I was able to see the first proto type they came up with and they had to change a lot to get it where it is now.

68293

Merry Xmas!!

rotflmfao!!!! :p:hurray::iamwithstupid::rofl::biggrinjester:

Haha, Murray Christmas John!

John P

12-24-2010, 12:46 PM

Merry Xmas to you to Buddy.

endeavor1

12-24-2010, 02:03 PM

Nice looking Sax!!!

endeavor1

12-24-2010, 02:04 PM

Merry Xmas to both you phuckers

Coolerman

12-24-2010, 06:06 PM

Yipeeeeeeeeeeeeeeeeeeee Bob

Hey Bob, seeing your polished PSI's inspired me to do a little polishing myself.

Here are some before and after pics of our muffler can/bbq's that I gave a light polish to today. I only spent about an hour per side, but it made such a difference. After 10hrs of running, they will probably look the same as if I had spent a whole weekend giving them a mirror finish.

endeavor1

12-25-2010, 03:42 AM

So did dennis ever notice???? lol

Coolerman

12-25-2010, 11:34 AM

So did dennis ever notice???? lol

lmao, He was in the bilge for about 20mins, and then I started pointing out brackets that I thought we should get polished. I did that for a couple mins, and still, nothing. Finally, I said that we should get everything polished to match the mufflers..... Then he noticed. I was laughing my ass off, and then of course he said, "Wait till you get old.... I'm gonna wack you with my cane!" haha

Ratickle

12-25-2010, 11:40 AM

lmao, He was in the bilge for about 20mins, and then I started pointing out brackets that I thought we should get polished. I did that for a couple mins, and still, nothing. Finally, I said that we should get everything polished to match the mufflers..... Then he noticed. I was laughing my ass off, and then of course he said, "Wait till you get old.... I'm gonna wack you with my cane!" haha

.....

Merry Christmas
http://i730.photobucket.com/albums/ww310/ptrose/seriousxmas4-1.gif

Coolerman

12-25-2010, 12:43 PM

.....

Merry Christmas
http://i730.photobucket.com/albums/ww310/ptrose/seriousxmas4-1.gif

LMAO, where do you get this stuff? haha

Merry Christmas Paul!

Coolerman

12-25-2010, 12:45 PM

Hey Bob, seeing your polished PSI's inspired me to do a little polishing myself.

Here are some before and after pics of our muffler can/bbq's that I gave a light polish to today. I only spent about an hour per side, but it made such a difference. After 10hrs of running, they will probably look the same as if I had spent a whole weekend giving them a mirror finish.

Also, if anyone is looking to get a quick easy polish job.... and you know we all are, here is what I did:

I used a palm sander and started with 400grit, then 600/800/1000. I then tried using a rough polishing compound on the 1000 grit instead of using a polishing wheel, and to my surprise, it worked pretty well.

Only 2hrs of spare time, and it made the bilge look $10k nicer.

endeavor1

12-25-2010, 01:29 PM

.....

Merry Christmas
http://i730.photobucket.com/albums/ww310/ptrose/seriousxmas4-1.gif

Merry Xmas Paul :26:

EXCESS ENERGY

12-25-2010, 09:04 PM

EXCESS ENERGY

12-25-2010, 09:06 PM

lmao, He was in the bilge for about 20mins, and then I started pointing out brackets that I thought we should get polished. I did that for a couple mins, and still, nothing. Finally, I said that we should get everything polished to match the mufflers..... Then he noticed. I was laughing my ass off, and then of course he said, "Wait till you get old.... I'm gonna wack you with my cane!" haha

Ya better watch out for that CANE boy:beatdeadhorse5:

EXCESS ENERGY

12-25-2010, 09:08 PM

Also, if anyone is looking to get a quick easy polish job.... and you know we all are, here is what I did:

I used a palm sander and started with 400grit, then 600/800/1000. I then tried using a rough polishing compound on the 1000 grit instead of using a polishing wheel, and to my surprise, it worked pretty well.

Only 2hrs of spare time, and it made the bilge look $10k nicer.

Bilge looks good, keep up the good work. Bob

Coolerman

12-25-2010, 11:53 PM

Looks good Jason. I"ll have to send you some of my magic poshion, some DWG metal polish , a nice soft rag, and a mexican. Ha Ha Merry Xmas:driving: Bob

lmao, mexicans can be had cheap these days! :26::26:

Merry Christmas Bob!

endeavor1

12-26-2010, 01:11 AM

lmao, mexicans be had cheap these days! :26::26:

Im running a special on them this week, buy 5 and get 1 free and for you guys, i ll even throw in a sombrero and a donkey.... :reddevil: :willy_nilly: :26:

Coolerman

12-26-2010, 01:37 AM

Im running a special on them this week, buy 5 and get 1 free and for you guys, i ll even throw in a sombrero and a donkey.... :reddevil: :willy_nilly: :26:

I'm not concerned about the mexicans, but does the donkey have a green card?!? :beatdeadhorse5::huh:

endeavor1

12-26-2010, 02:04 PM

I'm not concerned about the mexicans, but does the donkey have a green card?!? :beatdeadhorse5::huh:

Of course.....:dupe:

offshoreexcursion

12-29-2010, 05:39 AM

awesome coolers!

sweet addiction

12-30-2010, 11:25 PM

:smash:

I'm not concerned about the mexicans, but does the donkey have a green card?!? :beatdeadhorse5::huh:

Coolerman

03-03-2011, 12:50 AM

Figured out the polishing process. Took forever, but they turned out really nice.

Nevr2nd

03-03-2011, 10:14 AM

Sax,
That almost looks like a mugshot, did u photo shop it in??

BTW, Still waiting for my snowcone!

endeavor1

03-03-2011, 01:50 PM

LMAO, your dad is finally getting some work out of you.

Coolers are looking good

endeavor1

03-03-2011, 01:51 PM

BTW, Still waiting for my snowcone!

Ive got a snowcone for you..... :lurk5: :reddevil:

Nevr2nd

03-03-2011, 07:00 PM

Ive got a snowcone for you..... :lurk5: :reddevil:

I'm sure its tainted, I'm gonna pass, Thanks anyway.....I think.

endeavor1

03-04-2011, 12:13 AM

I'm sure its tainted, I'm gonna pass, Thanks anyway.....I think.

oh calm down, just teasing ya.....lol :party:

We dont have snowcones in TX anyway.... :26:

Im moving to KS here in a couple weeks, Are you gonna be running the Dam to Dam or Support the Troops runs this year on LOTO?

Coolerman

03-04-2011, 01:18 AM

Sax,
That almost looks like a mugshot, did u photo shop it in??

BTW, Still waiting for my snowcone!

lmao, i had to lighten the photo so you could actually see me. I was a much bigger than the photos show.

Coolerman

03-04-2011, 01:19 AM

Sax,
That almost looks like a mugshot, did u photo shop it in??

BTW, Still waiting for my snowcone!

haha, give me a ring/pm if you need some coolers!

John P

03-04-2011, 08:36 AM

Glad to see you getting your hands dirty.

Nevr2nd

03-04-2011, 12:10 PM

oh calm down, just teasing ya.....lol :party:

We dont have snowcones in TX anyway.... :26:

Im moving to KS here in a couple weeks, Are you gonna be running the Dam to Dam or Support the Troops runs this year on LOTO?

Lmao,
Dam to dam?? When is that??

Monopoly 46

03-04-2011, 03:54 PM

may 20th

Nevr2nd

03-04-2011, 04:01 PM

Dam.... I'll be lucky to be able to put fuel in my boat, these gas prices are killing me.....Dam.

You see there I went Dam to Dam. Ha ha.

Coolerman

03-04-2011, 04:24 PM

You went Dam to Dam, but at least you haven't gone Oh Chit. I think that's what happens when you blow a motor up..... lol

endeavor1

03-04-2011, 05:57 PM

or throw a driveshaft..... :huh:

Nevr2nd

03-05-2011, 06:54 PM

You went Dam to Dam, but at least you haven't gone Oh Chit. I think that's what happens when you blow a motor up..... lol

Coolerman is it now???

I hope I don't ever have to say that or to have feel that!!lol.
:driving:

offshoreexcursion

03-18-2011, 04:54 PM

I was wondering today why Ham Lake sounded so firmiliar to me. Finally figured it out..... Coolerman! We are loading cars at the co parts auction. Dreaming about boats while I drive! Wish we had time to stop by and check out that sweet BT or yours!

Ratickle

04-30-2011, 11:53 AM

How are you doing on finishing the coolers Jason??????

Any new testing?

Or do you still have a frozen lake??????

Coolerman

04-30-2011, 04:11 PM

Hey Paul! Things are going pretty well. We have a fair amount of potential customers right now, but only 1 sale.

Got the website up www.pfintercoolers.com

Also, if ya'll could like our facebook page, that would be awesome. http://www.facebook.com/profile.php?id=511710661#!/pages/PF-Marine-Intercoolers/189509671068911

Coolerman

06-12-2011, 03:59 AM

http://www.youtube.com/watch?v=yiny0rcM_3E Just got a vid up

Ratickle

06-12-2011, 11:21 AM

http://www.youtube.com/watch?v=yiny0rcM_3E Just got a vid up

Did I see 1194 Torque and 1543 HP ?

Coolerman

06-12-2011, 01:50 PM

1547hp @ 6800 and 1329ft/lbs @ 4900 in the vid.

Previously, we have made 1570hp @ 6800 and 1380ft/lbs @ 4600, but that was a bit different tuneup as far as timing and AF goes.

Ratickle

06-12-2011, 02:34 PM

1547hp @ 6800 and 1329ft/lbs @ 4900 in the vid.

Previously, we have made 1570hp @ 6800 and 1380ft/lbs @ 4600, but that was a bit different tuneup as far as timing and AF goes.

Must need more boost......:sifone::sifone::sifone:

Coolerman

06-12-2011, 04:26 PM

Must need more boost......:sifone::sifone::sifone:

LOL, there is still alot left on the table with this blower and intercooler combo. Keep in mind, these numbers were achieved using carbs, msd distributor, crane ignition, standard blower intake and 23* heads, all while keeping the intake temps under 100*F with only 10gpm of flow through the intercooler.

Nevr2nd

06-13-2011, 06:13 PM

1547hp @ 6800 and 1329ft/lbs @ 4900 in the vid.

Previously, we have made 1570hp @ 6800 and 1380ft/lbs @ 4600, but that was a bit different tuneup as far as timing and AF goes.

Soooooo, let me see if I comprehend this properly, ..........my snowcone is gonna take longer to make???? WTH???
:party:

EXCESS ENERGY

06-13-2011, 10:07 PM

LOL, there is still alot left on the table with this blower and intercooler combo. Keep in mind, these numbers were achieved using carbs, msd distributor, crane ignition, standard blower intake and 23* heads, all while keeping the intake temps under 100*F with only 10gpm of flow through the intercooler.

Jason, you guys happy where you ended up on the carbs. I need to order my. Bob

old377guy

06-14-2011, 11:11 AM

LOL, there is still alot left on the table with this blower and intercooler combo. Keep in mind, these numbers were achieved using carbs, msd distributor, crane ignition, standard blower intake and 23* heads, all while keeping the intake temps under 100*F with only 10gpm of flow through the intercooler.

Keep us posted and let us know when you start making the BIG horspower:sifone:

Coolerman

06-15-2011, 09:46 PM

Jason, you guys happy where you ended up on the carbs. I need to order my. Bob

Hey Bob, just saw your FB message. The carbs turned out pretty well. Not prefect, but we are definitely happy with them. Dennis knows he has to call you.

Coolerman

06-15-2011, 09:46 PM

Soooooo, let me see if I comprehend this properly, ..........my snowcone is gonna take longer to make???? WTH???
:party:

These snowcones won't melt!!! :cheers2: Nice and frosty.

Coolerman

06-15-2011, 09:47 PM

Keep us posted and let us know when you start making the BIG horspower:sifone:

lmao, let me know when #6 upgrades are available! lol :driving:

Coolerman

06-24-2011, 02:24 AM

Here are some new waterpickups we built so that the new intercoolers can get enough water. We should have them back from the welding shop mid next week, and then give them a quick touch up polish. Also, the first inch or so of the pickup has been expanded so you can put different length pipe inserts in there to adjust the height of your pickup.

Nevr2nd

06-24-2011, 11:35 AM

rschap1

06-24-2011, 01:31 PM

coat hooks, right?

Coolerman

06-25-2011, 04:31 PM

wow, those are the nicest snowcone dispensers I have ever seen!!

They just help make the snowcones faster, and colder!

Coolerman

06-25-2011, 04:31 PM

coat hooks, right?

Those would be the most expensive coat hooks that I have ever seen....... lol :biggrinjester:

endeavor1

06-25-2011, 08:42 PM

wow, those are the nicest snowcone dispensers I have ever seen!!

:smash: :iamwithstupid:

Coolerman

08-24-2011, 12:09 AM

locked and loaded for loto

EXCESS ENERGY

08-24-2011, 06:28 AM

locked and loaded for loto

Sweet, Good luck guys, be careful. Get plenty of video. Bob:driving:

Ratickle

08-24-2011, 07:09 AM

Good luck guys. I'm really rooting for the King's of the BT'rs to show everyone the way.......

Really wish we could be down there for this one. Unfortunately Terri has a business event this weekend there is no way out of. I'll be watching on the internet. Tell "Dad" no early cutout's........

Nevr2nd

08-24-2011, 09:20 AM

locked and loaded for loto

Awesome!!

See you there. Safe travels!!

rschap1

08-24-2011, 10:04 AM

Good Luck

Coolerman

08-24-2011, 03:02 PM

Thanks everyone. We won't take top vee, but we hope to win our class again.

Ratickle

08-24-2011, 03:29 PM

Thanks everyone. We won't take top vee, but we hope to win our class again.

Don't give up so early.......:smash:

Lance and Shelly may look you up. They live down there, had the Octane SVL, and is thinking about a BT. Take them for a ride if you get a chance. Hell, stay at their house.......:rolleyes:

They're also the ones who put the drag motor in their SVL for last years shootout and made them sweat......:rofl:

endeavor1

08-25-2011, 12:36 AM

See ya friday at Dog Days Sax.

endeavor1

08-25-2011, 12:50 AM

locked and loaded for loto

I think you missed a spot while cleaning Sax. :rofl:

Coolerman

09-08-2011, 11:01 PM

opps

Coolerman

09-08-2011, 11:32 PM

Just because we can

endeavor1

09-09-2011, 09:50 AM

LMFAO

endeavor1

09-09-2011, 04:03 PM

Turns out, bears dont like being cornered and called out do they? :huh:

John P

09-09-2011, 05:24 PM

Endeavor I have to ask why do you want people to think you are in Texas when you live in Kansas?

Ratickle

09-09-2011, 07:04 PM

Endeavor I have to ask why do you want people to think you are in Texas when you live in Kansas?

I think it has something to do with Dorothy and red high heeled shoes:eek:......

Coolerman

09-09-2011, 07:13 PM

I think it has something to do with Dorothy and red high heeled shoes:eek:......

and her little dog to!!!

Nevr2nd

09-10-2011, 12:14 PM

and her little dog to!!!

Lmfao!!!

endeavor1

09-10-2011, 07:47 PM

Endeavor I have to ask why do you want people to think you are in Texas when you live in Kansas?

Im just misplaced right now. Still have property down there so I claim it as home still. Thanks for taking notice.... :sifone:

Nevr2nd

09-10-2011, 09:20 PM

Im just misplaced right now. Still have property down there so I claim it as home still. Thanks for taking notice.... :sifone:

Did your nose stop bleeding???

Sax popped you straight in the face!!! Ha ha.
I mean ......how dare him?? :boxing_smiley:

endeavor1

09-11-2011, 10:50 AM

Did your nose stop bleeding???

Sax popped you straight in the face!!! Ha ha.
I mean ......how dare him?? :boxing_smiley:

LOL, no biggie. You know Sax has to come here in 2 weeks and karma is a
B!TCH... I know, used to date her im sure:bump:

Coolerman

09-11-2011, 02:03 PM

karma is a
B!TCH...

Can I crash at your place? :cheers2::kiss:

Coolerman

09-11-2011, 02:04 PM

:driving:

endeavor1

09-11-2011, 05:21 PM

Coolerman

09-11-2011, 06:30 PM

LMFAO>>>>>

Your always welcome at my place.Brayden needs someone to beat up on besides me, Jess, John, Michelle, Clint, a customers boat, bell housings, TxHouse.... you get the point.....:boxing_smiley:

As long as I don't sneak upstairs and say, "My turn!"

Also, do you have continental breakfast?

endeavor1

09-11-2011, 09:50 PM

As long as I don't sneak upstairs and say, "My turn!"

Also, do you have continental breakfast?

:sifone:

John P

09-12-2011, 08:12 AM

As long as I don't sneak upstairs and say, "My turn!"

Also, do you have continental breakfast?

I think they close the door now. :kiss::driving::ack2::willy_nilly::smash:

Nevr2nd

09-12-2011, 09:37 AM

As long as I don't sneak upstairs and say, "My turn!"

Also, do you have continental breakfast?

LOL, I believe I read that he does....... in the brochure.
Plus free local calls. (Escort Service).

Coolerman

09-12-2011, 12:21 PM

I think the only escort service his hotel offers is on Fords.

Coolerman

09-12-2011, 12:21 PM

I think they close the door now. :kiss::driving::ack2::willy_nilly::smash:

lmfao, monkey see monkey want to do to!

endeavor1

09-12-2011, 04:32 PM

lmfao, monkey see monkey want to do to!

Finally you see where im coming from.... :bump:

endeavor1

09-12-2011, 04:33 PM

I think they close the door now. :kiss::driving::ack2::willy_nilly::smash:

Sometimes.... :smash:

he asked the other day about "boat grandma"

John P

09-12-2011, 06:31 PM

Sometimes.... :smash:

he asked the other day about "boat grandma"

I'm not sure I want to know what he asked about! :kiss::willy_nilly::toetap05:

EXCESS ENERGY

09-12-2011, 07:26 PM

I think the only escort service his hotel offers is on Fords.

Easy now. LOL

Coolerman

10-29-2011, 11:33 PM

Can't believe I never posted a pic of these beasts!!!

Coolerman

10-29-2011, 11:44 PM

Just sold a set to Canada as well.....

Ratickle

10-30-2011, 07:04 PM

Can't believe I never posted a pic of these beasts!!!

Sweet......

Coolerman

10-30-2011, 09:48 PM

here's another setup.... GAMER CHANGER! lol :smash::driving:

Nevr2nd

10-31-2011, 09:40 AM

here's another setup.... GAMER CHANGER! lol :smash::driving:

Does it also double as a PO Box at the Post Office?? Ha ha.

Coolerman

10-31-2011, 11:58 AM

Does it also double as a PO Box at the Post Office?? Ha ha.

It will haul the mail........ :drool5:

Nevr2nd

10-31-2011, 12:45 PM

It will haul the mail........ :drool5:

That's for sure!!!

Ratickle

11-01-2011, 10:37 AM

here's another setup.... GAMER CHANGER! lol :smash::driving:

I like it.......:hurray::hurray::hurray:

Now if you'd just send a pair out to each of us for some Serious testing, over the course of the next year or two, we'll write nice field test articles for you to place in your worldwide advertising program.....

sweet addiction

11-01-2011, 09:49 PM

Holy Chit those are sweet.

endeavor1

11-02-2011, 02:44 PM

Holy Chit those are sweet.

I see that you got a new ride Jared...??? Care to elaborate in our bashing thread? Might as well.... :sifone:

Coolerman

12-02-2011, 11:52 PM

more products coming........ unrelated to induction systems though. Any guess's? :evild:

Ratickle

12-02-2011, 11:57 PM

more products coming........ unrelated to induction systems though. Any guess's? :evild:

If we guess right, what do we get????

offshoreexcursion

12-03-2011, 12:26 AM

Guess???? A COOLERMAN work out video!!!

John P

12-03-2011, 08:21 AM

Jason are you back into the exhaust business again?

offshoreexcursion

12-03-2011, 11:38 AM

I like that guess!

Nevr2nd

12-03-2011, 01:27 PM

more products coming........ unrelated to induction systems though. Any guess's? :evild:
Trannies????

Ratickle

12-03-2011, 01:43 PM

They've done exhaust headers. So, probably not.....

What about that sweet muffler system they have? Merc kind of copied it. Overseas and CA have very strict rules. MI is getting crazy on noise, etc.....

Coolerman

12-03-2011, 04:40 PM

Yes....... a workout video! The first part we will work on stern lifting. It involves understanding how to trim your lower units.

Also, the trannies are for my other business venture.......

Ratickle

12-03-2011, 04:53 PM

Yes....... a workout video! The first part we will work on stern lifting.

Also, the transvestites are for my other business venture.......

:eek:

endeavor1

12-03-2011, 08:38 PM

Jason are you back into the exhaust business again?

Hmmm..... maybe that or a B-MaxMachine worx platinum shaftSCX trim tab limiter????? lol

Hope all is going well for ya buddy

Tinkerer

12-03-2011, 10:57 PM

The super charger is allmost bigger than the engine...

Nevr2nd

12-04-2011, 12:23 AM

Yes....... a workout video! The first part we will work on stern lifting. It involves understanding how to trim your lower units.

Also, the trannies are for my other business venture....
...

So your finally get into the Circus ...........dressing your tranny as a clown and making snowcones, C16 flavor???

Coolerman

12-04-2011, 03:23 AM

Well, I'm just gonna start off with trannie fluids for now.........

Coolerman

12-28-2011, 01:29 PM

Just got our lowers back from blueprinting..... Wilson said they were no better/worse than typical mercury quality. Anxious to get these on the water! Cleaning gaskets today and getting things ready to assemble the motors. Pistons should be here soon, and cranks shouldn't be far behind. Carbs should be here soon, cams are on order.

endeavor1

12-28-2011, 10:43 PM

Sounds like its coming together nicely for you.Glad to hear it.

offshoreexcursion

12-29-2011, 12:20 PM

Sounds awesome! Jelous and excited for you! Post some pics of your progress.

Coolerman

01-24-2012, 11:44 PM

Last run from 2011 before putting it away for the winter. Was at about 7/8 throttle until 120/122. Still had the drives and tabs down a bit, had to back off for traffic/boat wakes.

http://www.youtube.com/watch?v=E5d5TsKT0jg

http://youtu.be/E5d5TsKT0jg

John P

01-25-2012, 11:51 AM

I seen 127.

Ratickle

01-26-2012, 08:44 AM

Takin it easy......:cool:

offshoreexcursion

01-31-2012, 01:28 AM

YES 127...Looks awesome!

Ratickle

01-31-2012, 08:42 PM

Jason, what's the max RPM you spin those BadBoys at?????

Is that the same props as at the shootout?

Coolerman

02-01-2012, 01:42 AM

Jason, what's the max RPM you spin those BadBoys at?????

Is that the same props as at the shootout?

7200-7300 is about the max we would spin that set of motors to. And yes, those were the props used at the shootout.

offshoreexcursion

02-15-2012, 10:15 PM

Dropped off a load in Ham Lake today! Thought about stopping by to see the top secret project but then realized you are prob on your way to Miami to Debut it!!! :cheers2:

Ratickle

02-16-2012, 08:18 PM

We're waiting for all the info.....:toetap05:

Coolerman

02-16-2012, 08:48 PM

Dropped off a load in Ham Lake today! Thought about stopping by to see the top secret project but then realized you are prob on your way to Miami to Debut it!!! :cheers2:

Next time you are in the area, give me a call. Stop by anytime! 612-202-9359

The newest thing right now is dual & quad pulley belt tensioners.