PDA

View Full Version : Moving parts off the shelf


MERPerformance
10-29-2009, 07:40 PM
1 Set of Comp Cams 1.7 take-off rockers.$150
MERPerformance
10-29-2009, 07:44 PM
1.8 Comp Cams rockers 1/2 set plus 3 take-offs $90
MERPerformance
10-29-2009, 07:49 PM
Crane Gold 1.7 Almost new. 3 of them have slight damage from push rod, guide plate failed. $100
MERPerformance
10-29-2009, 07:55 PM
2 Blower Shop Inner cooler cores take-outs $300 each
MERPerformance
10-29-2009, 07:59 PM
Engine Knock System From Livorsi make me a fair offer on this, I have 2 kits
MERPerformance
10-29-2009, 08:02 PM
Starter take-off $120
MERPerformance
10-29-2009, 08:04 PM
CMI tails 4" new Straight $200
MERPerformance
10-29-2009, 08:07 PM
New 4" tips $150
MERPerformance
10-29-2009, 08:09 PM
Trim tabs $300 SOLD?
MERPerformance
10-29-2009, 08:19 PM
2 sets valve covers, 2 piece 1 set missing lower plates $100
Bottom plates are chromed covers are powder-coated. Like new.
MERPerformance
10-29-2009, 08:24 PM
Like new helm unit -6 fittings, 75cc this was a take off it was replaced with a 160cc $110
MERPerformance
10-29-2009, 08:27 PM
30" Bravo one, labbed take off $250
MERPerformance
10-29-2009, 08:43 PM
JE Pistons 4.500 bore 1.395 compression height. These are take outs.
Need wrist pin bosses lightly honed from removing spiral locks. I believe I have 10-12 pistons
MERPerformance
10-29-2009, 08:48 PM
Used JE pistons inverted dome 4.500 bore 1.345 compression height. $300
PARADOX
10-29-2009, 09:17 PM
New 4" tips $150

How many tips do you have ? I need 4. You got 4 I'm interested.
14 apache
10-29-2009, 09:27 PM
Sent pm on trim tabs i will take them.
klaw
10-30-2009, 09:43 AM
Like new helm unit -6 fittings, 75cc this was a take off it was replaced with a 160cc $110

do you know is tis would be to small a helm for a ITS transom assembly it is on a 20 cig with a blackhawk
DAREDEVIL
10-30-2009, 10:52 AM
JE Pistons 4.500 bore 1.395 compression height. These are take outs.
Need wrist pin bosses lightly honed from removing spiral locks. I believe I have 10-12 pistons

With a 4 inch stroke ,,, would these be 9.5:1 compression ??
MERPerformance
10-30-2009, 06:35 PM
How many tips do you have ? I need 4. You got 4 I'm interested.
Sorry only 1 pair
MERPerformance
10-30-2009, 06:42 PM
do you know is tis would be to small a helm for a ITS transom assembly it is on a 20 cig with a blackhawk
It came off of a 33' Fountain with #4 speedmasters, twin Mayfair rams with 5/8 " shafts. We replaced them because; my customer had lost some of his movement in his right arm and we went to twin pumps and larger rams. It worked fine before we took it off.
MERPerformance
10-30-2009, 06:45 PM
With a 4 inch stroke ,,, would these be 9.5:1 compression ??
What block and rod length do you have?
DAREDEVIL
10-30-2009, 07:31 PM
What block and rod length do you have?

Chevy bowtie block ( gen IV ) rod length ????? LOL
Steve Miklos
10-31-2009, 04:15 PM
I will take valve covers
Steve
klaw
11-04-2009, 11:54 AM
do you know is tis would be to small a helm for a ITS transom assembly it is on a 20 cig with a blackhawk

how about 100 shipped slow boat to 60050
MERPerformance
11-11-2009, 08:35 PM
Was trying to delet sold items. THESE ITEMS ARE SOLD!
Trim tabs
Helm pump
1.7 competition cams rockers
Valve covers