Activity Stream
-
Older Activity
-
Today, 10:11 PMYou might want to give Bblades a call. https://bblades.com/used-propeller-list/288 replies | 88140 view(s) -
Today, 09:58 PMThat was a 25'...They are a good looking Hull.11 replies | 267 view(s) -
Today, 09:40 PMThere is a Bernie meme for you Bobcat, The scene where they went down and buried him in the sand.14971 replies | 1218068 view(s) -
Today, 09:38 PMThe Glass Stream makes a nice looking CC. Not sure how big of a wave they will take.11 replies | 267 view(s)
-
11 replies | 267 view(s)
-
Today, 07:55 PMOkay, We couldn't have picked a better Day to go...Opening Day Crowds weren't bad...and it was a perfect 76 Degrees. We started off in the Trailered...11 replies | 267 view(s)
-
Today, 05:51 PMLooks like the pipes you have now will require hatch work. You should be able to have pipes fit under the hatch. Your engines sure look nice. ...330 replies | 50409 view(s) -
Today, 05:45 PMI idle my 509's about 1000. works out to be about 750 / 800 in gear. Being a particular old fart I have me routines. Adjusted mine to idle relatively...330 replies | 50409 view(s)
-
Today, 02:50 PMHard to say what exactly I need at this point but its been confirmed that the two sets I have are for a Bravo drive setup. I need to go take...330 replies | 50409 view(s) -
Today, 02:47 PMJim, I have been trying to read and learn all about reversion. I believe I get the concept. I read about these 540 engines and they do say you need...330 replies | 50409 view(s)
-
Today, 01:28 PMI ran the 27"s a couple times last summer. My original 26 Hydromotive QUAD IV set worked better. They carried boat better needing less trim to run....288 replies | 88140 view(s)
-
Today, 12:18 PMSpeed on the Water started a thread Nor-Tech 500 Sport Center Console Hull No. 1 Getting Dressed At SMD in On The DockThe first Nor-Tech 500 Sport Center Console is in the paint booth at Stephen Miles Design,...0 replies | 6 view(s) -
Today, 11:40 AMi totally agree with that . and there is much more to come of un neccesary restrictions on our freedom18 replies | 259 view(s) -
Today, 11:04 AMFly It Friday epic flight from Boyne Thunder 201633 replies | 2245 view(s)
-
Today, 09:53 AMEnjoy !! Happy Friday14971 replies | 1218068 view(s) -
Today, 09:52 AMGotta give credit where due666 replies | 92416 view(s)
-
Today, 09:51 AMMaybe you could get lucky, start posting, and find someone that has what you need and needs what you have... trade risers. Would be nice if...330 replies | 50409 view(s)
-
Today, 09:39 AMMight want to mock up everything you want to do using 4” PVC pipe/fittings from transom to the first weld on the tail at the manifold. Then send them...330 replies | 50409 view(s)
-
Today, 08:56 AM666 replies | 92416 view(s)
-
Today, 08:47 AMMornin!:seeya: Heading up to Hawks Cay with Charlie for the Boat Show around Noon.. They better be serving Beer:reddevil:14971 replies | 1218068 view(s)
-
Yesterday, 10:29 PMBefore I raised and re rigged my tail pieces had a wedge installed where the gaskets go to raise exit end of pipe up to go through existing holes....330 replies | 50409 view(s)
-
Yesterday, 10:15 PMTough call. You want as few bends and welds as possible. Welding pipes is a specific skill. Tail pieces or any exhaust for that matter that leak can...330 replies | 50409 view(s)
-
Yesterday, 08:20 PMBAMM! Just needed to say that. Long week.14971 replies | 1218068 view(s)
-
Yesterday, 07:57 PMIm thinking i can cut on the second weld to the right in this photo, put that 45 on there and reweld that straight part to the end of the 45 that...330 replies | 50409 view(s)
-
Yesterday, 07:31 PMI have two sets of Gils just like that, plus a pump and four mufflers and I can't give them away and they are sitting outside by my trash. I...330 replies | 50409 view(s) -
Yesterday, 07:02 PMJim I have 4 complete sets of gil manifolds and 3 sets of tailpipes. 1 set off the 420's was stolen out of the boat many years ago. I'm wondering...330 replies | 50409 view(s)
-
Yesterday, 06:48 PMLook in my project thread here on this forum. Fountain/ Lucky and Perfect . Post 198 and 199 shows pix of my exhaust. I suspect you need something...330 replies | 50409 view(s)
-
Yesterday, 06:29 PMhttps://www.cpperformance.com/instructions/420-901180i.pdf This is a start.330 replies | 50409 view(s)
-
Yesterday, 06:20 PM330 replies | 50409 view(s)
-
Yesterday, 06:13 PMCongrats on getting our drives in order. Exhaust tailpieces come many different ways. I can't say for sure what you have other then bravo tails....330 replies | 50409 view(s)
